1/28 2WD indoor Racer

JOM280108: JR128-R01 2WD RTR-STOCK-RC-Car-Set / GT01-white

About this RTR-STOCK Car Model

JR128-R01 series models are 1:28 scale ultra small high performance 2WD indoor racing cars with a lot of very advanced opportunities for fine tuning and car setup.

The cars are already equipped with a micro servo for steering, a small 2.4 GHz receiver and an ESC (Electronic Speed Controller) running with 1S / 3.7V Lipo batteries, providing 5.5V current for receiver and steering servo.

Various other commercially available steering servos, micro receivers and micro car ESCs for brushed or brushless motors from other brands can be built in and used in this car.

Ask your dealer for our brushless motor and ESC-System and for our 2S Lipo batteries, if you need 8.4V power supply for your preferred electronics.


Included in each set

  • 9 ball bearings MR63ZZ
  • ball differential with 64dp fine pitch (V-groove PN)
  • 1S / 3.7V Lipo battery + charger
  • micro steering servo

Fully assembled Ready to Run JR128-R01 STOCK RC Car:

• High Resistance Plastic Chassis with Alu T-Bar and Brass Motor Plate low.
• Jomurema Design GT01 Body white and light Car Glass.
• Transponder Holder.
• Adjustable Front Suspension
• Adjustable Rear Suspension
• 9x Ball Bearings
• Ball Differential (V-Groove produced under license of PN-Racing)
• Brushed STOCK Motor / 130 Class
• FS-GT2 / 2.4GHz digital proportional Receiver
• Micro Steering-Servo;
• 1S / 3.7V programmable brushed ESC

Lithium Polymer (Lipo) Battery:

• 1S / 3.7V / 840mAh / 25C Lipo Battery

Charger for Lipo Battery:

• 1S / 3.7V / Lipo Charger
• Approx. 1A charging Current

Manuals and Decal:

• Manual for JR128-R01 indoor Racer
• Manual for FS-GT2 / 2.4 GHz digital proportional Radio Control System
• Color Decal for Car Body

Miscellaneous Parts and Tools (8 Bags):

• Cross-Screwdriver; Hex-Wrench-1.5mm; +3 different plastic Tools
• Front Body-Holder-Adjustment-Set for many other Car Bodies
• Miscellaneous adjustment Parts and Washers
• Steering- Servo-, Rear Body-Holder and Adjustment Parts
• Other Pinions and replacement Gear for Change of Car-Speed
• Steel Parts, Replacement Parts and Springs for Change of Setup
• O-Rings for Replacement
• Screws for Replacement

FS-GT2 / 2.4 GHz digital proportional Radio Transmitter:

• Channels: 2channels; Model type: car / boat
• RF power: less than 20dbm; Modulation: GFSK
• Code type: digital; Sensitivity: 1024
• Low voltage warning: yes (less than 9V)
• DSC port: yes (3.5mm); Charger port: yes
• Power: 12vdc (1.5AA*8); Weight: 328g
• ANT length: 26mm;
• Size: 159*99*315mm; Color: black
• Certificate: CE, FCC

The STOCK Chassis offers the following Features:

• Caster-angle at front suspension adjustable in three positions: 1.1°, 2.7°, 4.4°.
• Camber-angle at front suspension left and right adjustable: from 0° to -2.5°.
• Toe-in / Toe-out adjustable at: 0°, +1°, +2°, -1°, -2°.
• Droop limits at front suspension free adjustable.
• Adjustable springs at front suspension.
• Ground clearance front and rear adjustable on 4 levels in steps of 0.7mm.
• Longitudinal damper with spring and droop-spring fully adjustable.
• Cross-dampers with springs for tweak adjustment.
• Rear scale body holder adjustable in height with included washers. Second rear scale body holder for wider scale bodies included.
• Front scale body holder set adjustable to most scale bodies from other brands for wide front and 98mm or 102mm wheelbase.


Technic Base RTR with stock motor

Click on the buttons for more information!